Enhanced grip and performance

PIP is constantly bringing new innovations to our general purpose glove line. With a variety of superior coating and grip technologies, combined with comfortable liner materials, these products improve performance without sacrificing dexterity and comfort.

SHOWING 1-5 OF 5 ITEMS
1 of 1
FILTERS:
CLEAR ALL
Touchscreen Compatible
Nylon with Polyurethane Grip

G-Tek® VR-X™

Seamless Knit Nylon Glove with Polyurethane Advanced Barrier Protection Coating on Full Hand – Touchscreen Compatible

33-VRX180

  • Liner Material: Nylon
  • Gauge: 18
  • Coating: Polyurethane
  • Coating Coverage: Full Hand
  • Grip: Foam
  • Cuff: Knit Wrist
  • Construction: Coated Seamless Knit, Touchscreen Compatible, ESD Safe
  • Sizes: XS-XXL
  • Packed: 12 Dozen/Case

3111

EN 388 2016 Results: 3111XX

Abrasion: 3
Cut (Coupe Test): 1
Tear: 1
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ANSI Puncture Level: 2

Test Method: ASTM F1342

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

ESD Safe

ESD is an acronym for electrostatic discharge. This discharge is the rapid transfer of static between two different objects. Although ESD doesn’t typically cause harm to the human body - you might only experience it as a small, surprising shock - it can cause extensive damage to electrical equipment and sensitive instruments. This damage may either be permanent, causing the device to malfunction (known as a catastrophic failure), or it may occur on a smaller scale that would be difficult to detect before the device is sent out for service (known as latent defect).

FENTANYL PROTECTION

Test Method: ASTM D6978-05

In accordance with ASTM D6978-05, Personal Protective Equipment can be tested to ensure an effective barrier against Fentanyl. The ASTM D6978-05 Standard Practice for Assessment of Medical Gloves to Permeation by Chemotherapy Drug tests a breakthrough time of typically 240 minutes to determine if the PPE provides an effective barrier.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare

G-Tek® NeoFoam®

Seamless Knit Nylon Glove with NeoFoam® Coated Palm & Fingers - Medium Duty

34-605

  • Liner Material: Nylon
  • Gauge: 15
  • Coating: Neofoam
  • Coating Coverage: Palm & Fingers
  • Grip: Foam
  • Cuff: Knit Wrist
  • Construction: Coated Seamless Knit, Touchscreen Compatible
  • Sizes: S-XXL
  • Packed: 12 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 is used for uncoated gloves and the end point (failure) is the number of abrasion cycles when the first thread or yarn is broken. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
Nylon with NeoFoam Grip

G-Tek® NeoFoam®

Seamless Knit Nylon Glove with NeoFoam® Coated Palm, Fingers & Knuckles - Medium Duty

34-608

  • Liner Material: Nylon
  • Gauge: 15
  • Coating: Neofoam
  • Coating Coverage: Palm, Fingers & Knuckles
  • Grip: Foam
  • Cuff: Knit Wrist
  • Construction: Coated Seamless Knit, Touchscreen Compatible
  • Sizes: S-2XL
  • Packed: 12 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 is used for uncoated gloves and the end point (failure) is the number of abrasion cycles when the first thread or yarn is broken. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
MaxiFlex Nylon, Micro-Foam Nitrile

MaxiFlex® Endurance™

Seamless Knit Nylon Glove with Nitrile Coated MicroFoam Grip on Palm & Fingers - Micro Dot Palm - Touchscreen Compatible

34-844

  • Liner Material: Nylon/ Lycra
  • Gauge: 15
  • Coating: Nitrile
  • Coating Coverage: Palm & Fingers
  • Grip: MicroFoam
  • Cuff: Knit Wrist
  • Construction: Coated Seamless Knit, Touchscreen Compatible
  • Sizes: XXS - XL
  • Packed: 12 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 is used for uncoated gloves and the end point (failure) is the number of abrasion cycles when the first thread or yarn is broken. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
MaxiFlex Nylon, Micro-Foam Nitrile BEST SELLER

MaxiFlex® Ultimate™

Seamless Knit Nylon/Elastane Glove with Nitrile Coated MicroFoam Grip on Palm & Fingers - Touchscreen Compatible

34-874

  • Liner Material: Nylon/ Elastane
  • Gauge: 15
  • Coating: Nitrile
  • Coating Coverage: Palm & Fingers
  • Grip: MicroFoam
  • Cuff: Knit Wrist
  • Construction: Coated Seamless Knit, Touchscreen Compatible
  • Sizes: XXS - XXXL
  • Packed: 12 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 is used for uncoated gloves and the end point (failure) is the number of abrasion cycles when the first thread or yarn is broken. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
SHOWING 1-5 OF 5 ITEMS
1 of 1
pin Rep Finder
Compare ()
Clear All Compare
Okay, Got it.
X

ORDER SAMPLE

X

GET FIELD TRIAL